US Roof Calculator

How to Calculate Roof Pitch

Roof pitch is a single ratio — how much the roof rises over a 12-inch horizontal run — and you can measure it three ways without ever leaving the ground if you don't want to. This guide walks through the attic method (most accurate for homeowners), the roof-surface method, and the no-climb methods, then shows the formula that turns your measurement into angles, multipliers and material quantities.

Home › How to Calculate Roof Pitch

Method 1 — From inside the attic (most accurate, no roof climbing)

  1. Take a tape measure, a pencil and a level at least 12 inches long into the attic.
  2. Find a rafter you can reach. Hold the level against the underside of the rafter and make it perfectly level.
  3. From the point where the level touches the rafter, measure exactly 12 inches along the level and mark it.
  4. From that mark, measure straight down (vertically) to the underside of the rafter. That measurement is your rise.
  5. Your pitch is rise/12. A 6-inch drop means 6/12 pitch.

Measuring against the rafter's underside works because the rafter runs parallel to the roof surface. Avoid measuring against collar ties or the ridge board — only the rafter itself carries the slope.

Method 2 — On the roof surface

  1. Set a long level (or a straight board) on the roof surface with one end touching, pointing down-slope, and raise the other end until the bubble reads level.
  2. Measure 12 inches along the level from the contact point.
  3. Measure the vertical gap between that point on the level and the roof surface below it. That gap is the rise over a 12-inch run.

Only use this method on roofs you can already stand on safely — which, if you don't know the pitch yet, you probably shouldn't assume. The attic method exists precisely for this chicken-and-egg problem.

Method 3 — From the ground, a photo, or your phone

Phone inclinometer: most phones have a level/clinometer app. From inside the attic, lay the phone's edge along a rafter and read the angle; convert with the formula below (a 26.6° reading is 6/12). Or photograph the gable end square-on and measure the slope triangle in the photo with a ruler: rise and run in the photo keep the same ratio as the real roof.

From the ground with a speed square: sight along a rafter tail or the gable's rake trim from the yard. Rafter tails are cut parallel to the slope, and many roofers will also just tell you — the pitch is printed on most truss tags and many past roofing quotes.

The formula — and a worked example

Pitch = rise ÷ run, expressed over 12 (e.g. 6 ÷ 12 → "6/12") Angle = arctan(rise ÷ run) Multiplier = √(1 + (rise ÷ run)²) Slope % = (rise ÷ run) × 100

Worked example. In the attic you measure a 6-inch drop over 12 inches. Pitch = 6/12. Angle = arctan(6/12) = arctan(0.5) = 26.57°. Multiplier = √(1 + 0.25) = √1.25 = ×1.118 — every 100 sq ft of floor plan under this roof carries 111.8 sq ft of roof. Slope = 50%.

Feed any rise/run pair into the pitch calculator and it returns all four figures plus a rafter length; the pitch multiplier chart lists the standard pitches if you'd rather look yours up.

Sanity checks that catch bad measurements

  • Most US homes land between 4/12 and 9/12. A reading outside 2/12–12/12 deserves a second measurement.
  • Both slopes of a simple gable should read the same. If they don't, re-measure — additions and porches legitimately differ, main roofs rarely do.
  • A quarter-inch of rise error moves the multiplier by ~0.5% — acceptable. A full inch (7/12 read as 6/12) is a 3.6% area error across every downstream calculation.

Frequently asked questions

What is the formula for roof pitch?

Pitch = rise ÷ run, written over a run of 12. If a roof rises 6 inches over 12 inches of horizontal run, the pitch is 6/12. The angle is arctan(rise ÷ run) and the area multiplier is √(1 + (rise/run)²).

How do I measure roof pitch without going on the roof?

From the attic: hold a 12-inch level against the underside of a rafter, mark 12 inches along it, and measure the vertical drop to the rafter — that drop is your rise. A phone inclinometer laid along a rafter also works; convert its angle with arctan in reverse (pitch = tan(angle) × 12).

What does a 6/12 pitch mean in degrees?

26.57 degrees. 6/12 means the roof rises 6 inches per 12 inches of run, and arctan(6/12) = 26.57°. Its slope percent is 50% and its area multiplier is ×1.118.

Can I get roof pitch from Google Earth or a photo?

Approximately, yes: a square-on photo of the gable end preserves the rise/run ratio, which you can measure with a ruler. Satellite tools estimate pitch from shadows and imagery with varying accuracy — fine for a first budget, worth verifying in the attic before ordering materials.

Why do roofers write pitch as x/12?

Because framing is built around the 12-inch unit run: rafter tables, speed squares and cutting angles are all indexed to 'per foot of run'. Expressing every slope over 12 makes any two roofs instantly comparable and every rafter calculation a multiplication.

Sources & data

Geometry: standard rise-over-run roof mathematics — pitch multiplier = √(1 + (rise/12)²), rafter length from the Pythagorean theorem — as published in roofing measurement references and framing practice.

Data retrieved: 17 Nov 2026.

Disclaimer: This page gives a preliminary estimate, not a contractor quote. Figures are based on national published cost ranges and standard geometry, with the assumptions shown on the page. Your actual price or measurement will vary with location, roof complexity and condition, material grade, and contractor. Always obtain written quotes and verify critical measurements before buying materials.

Related calculators & guides

Keep going with the tools and guides homeowners use alongside this one:

Roof Pitch Calculator

Convert rise and run into pitch, angle in degrees, slope percent, multiplier and rafter length.

Roof Pitch Multiplier Chart

Every pitch from 1/12 to 12/12: angle, slope percent, multiplier and best materials.

Rafter Length Calculator

Common rafter length, rafter count and cut angles from span, pitch and spacing.

Roof Area Calculator

True roof square footage and roofing squares from footprint and pitch.

Hip Roof Calculator

Hip rafter length, ridge length and roof area for an equal-pitch hip roof.