US Roof Calculator

Roof Pitch Calculator: Pitch, Angle, Slope & Rafter Length

Roof pitch is one ratio — rise over run — but it gets quoted four different ways: as a pitch (6/12), an angle (26.57°), a slope percent (50%), and a multiplier (×1.118). Enter any rise and run and this calculator converts between all four, and works out rafter length for your span.

Home › Roof Pitch Calculator

Calculate your roof pitch

Your roof pitch

Pitch
—
Angle
—
Slope
—
Multiplier
—

    Geometry: pitch = rise ÷ run; angle = arctan(rise ÷ run); multiplier = √(1 + (rise ÷ run)²). See the full chart in our pitch multiplier chart.

    The four ways to say the same slope

    They are all the same measurement wearing different clothes:

    Pitch (x/12) = (rise ÷ run) × 12 Angle = arctan(rise ÷ run) → in degrees Slope percent = (rise ÷ run) × 100 Multiplier = √(1 + (rise ÷ run)²) → footprint × multiplier = roof surface

    Worked example — a 6/12 roof. Rise 6, run 12: ratio = 0.5. Pitch = 0.5 × 12 = 6/12. Angle = arctan(0.5) = 26.57°. Slope = 50%. Multiplier = √(1.25) = ×1.118 — so a 1,200 sq ft footprint under a 6/12 roof carries 1,342 sq ft of actual roof surface, and a rafter spanning a 12 ft horizontal run is 12 × 1.118 = 13.42 ft long before cuts and overhang.

    Pitch is not a matter of taste: it decides which materials are even allowed on the roof (standard shingles need 4/12 or steeper, or 2/12 with special underlayment), how much surface you are paying for, and how dangerous the roof is to walk. Our pitch multiplier chart lists every pitch from 1/12 to 12/12 with its best materials.

    Pitch conversion table (1/12 to 12/12)

    PitchAngleSlopeMultiplier
    1/124.76°8.3%×1.0035
    2/129.46°16.7%×1.0138
    3/1214.04°25.0%×1.0308
    4/1218.43°33.3%×1.0541
    5/1222.62°41.7%×1.0833
    6/1226.57°50.0%×1.1180
    7/1230.26°58.3%×1.1577
    8/1233.69°66.7%×1.2019
    9/1236.87°75.0%×1.2500
    10/1239.81°83.3%×1.3017
    11/1242.51°91.7%×1.3566
    12/1245.00°100.0%×1.4142

    Multipliers are exact geometry — √(1 + (rise/12)²) — rounded to four decimals. The two-decimal versions used in quick cost estimates (6/12 → ×1.12) differ by less than half a percent.

    Common pitch mistakes

    Confusing pitch with angle

    A "6 pitch" roof is not 6 degrees — it is 26.57°. And a 45° roof is 12/12, not "45 pitch". Mixing these up in a material order or a quote conversation is expensive.

    Measuring run wrong

    Run is the horizontal distance, never the slope distance. The standard measurement uses a 12-inch level: hold it level, and measure the vertical rise from its end down to the roof surface. See our step-by-step guide on how to calculate roof pitch for three ways to measure, including from inside the attic without climbing on the roof.

    Forgetting the multiplier when pricing

    Quoting materials off the footprint understates a 6/12 roof by 12% and a 12/12 roof by 41%. Every cost and material calculator on this site applies the multiplier for you when you enter a footprint.

    Frequently asked questions

    What is roof pitch?

    Roof pitch is the slope of a roof expressed as rise over run: how many inches the roof climbs vertically for every 12 inches it travels horizontally. A 6/12 pitch rises 6 inches per foot of run. It is the standard way US roofers, framers and material suppliers describe slope.

    How do I convert pitch to degrees?

    Angle = arctan(rise ÷ run). For 6/12: arctan(0.5) = 26.57°. Common conversions: 4/12 = 18.43°, 8/12 = 33.69°, 12/12 = 45°. The calculator and chart on this page cover the full range.

    What is the most common roof pitch in the US?

    6/12 is the most common residential pitch — steep enough to shed water and snow reliably and to accept every standard roofing material, shallow enough to walk during installation with basic precautions.

    What is the minimum pitch for shingles?

    Standard asphalt shingle installations require 4/12 or steeper. Between 2/12 and 4/12, shingles are only allowed with a full double layer of underlayment or an ice-and-water shield membrane. Below 2/12, use membrane or metal systems designed for low slopes instead.

    What is a pitch multiplier used for?

    It converts a flat footprint into true sloped surface area: footprint × multiplier = roof surface. Roofers use it to price jobs and order materials from a floor plan or satellite footprint without climbing the roof.

    Sources & data

    Geometry: standard rise-over-run roof mathematics — pitch multiplier = √(1 + (rise/12)²), rafter length from the Pythagorean theorem — as published in roofing measurement references and framing practice.

    Data retrieved: 17 Nov 2026.

    Disclaimer: This page gives a preliminary estimate, not a contractor quote. Figures are based on national published cost ranges and standard geometry, with the assumptions shown on the page. Your actual price or measurement will vary with location, roof complexity and condition, material grade, and contractor. Always obtain written quotes and verify critical measurements before buying materials.

    Related calculators & guides

    Keep going with the tools and guides homeowners use alongside this one:

    Roof Pitch Multiplier Chart

    Every pitch from 1/12 to 12/12: angle, slope percent, multiplier and best materials.

    How to Calculate Roof Pitch

    Three step-by-step methods, the formula, and a worked 6/12 example.

    Rafter Length Calculator

    Common rafter length, rafter count and cut angles from span, pitch and spacing.

    Roof Area Calculator

    True roof square footage and roofing squares from footprint and pitch.

    Hip Roof Calculator

    Hip rafter length, ridge length and roof area for an equal-pitch hip roof.