US Roof Calculator

Roof Area Calculator: Square Footage & Squares

Every roofing number — cost, bundles, underlayment, sheathing — starts from one figure: the true sloped area of your roof. Enter your building's footprint and pitch and this calculator converts them into real roof square footage and roofing squares, with a hip-roof allowance and a waste-adjusted order quantity.

Home › Roof Area Calculator

Calculate your roof area

Your roof area

True roof area
—
Roofing squares
—
With waste allowance
—

    Geometry: roof area = footprint × √(1 + (pitch/12)²). Overhangs are not included — add your eave overhang to the building dimensions if you want them counted.

    How roof area is calculated

    Footprint = building length × building width Roof area = footprint × √(1 + (pitch ÷ 12)²) ← the pitch multiplier Squares = roof area ÷ 100

    Worked example. A 40 ft × 30 ft house has a 1,200 sq ft footprint. At 6/12 pitch the multiplier is ×1.118, so the true roof area is 1,200 × 1.118 = 1,342 sq ft — 13.4 squares, or 1,476 sq ft to order at 10% waste. The flat footprint understates the job by 12%; on a 12/12 roof it would understate it by 41%.

    The multiplier works because a sloped plane is the hypotenuse of the rise/run triangle: for every 12 inches of horizontal run, the roof surface travels √(12² + rise²) inches. Divide by 12 and you have the factor. The full table lives in our pitch multiplier chart.

    Gable vs hip

    For a plain gable roof, footprint × multiplier is essentially exact (both slopes are simple rectangles). A hip roof has the same surface relationship, but its hips and rakes generate far more cutting waste, so this calculator adds a 5% complexity allowance when you select "hip" — a measuring convention, stated openly, not hidden in the math. Dormers, valleys and multiple roof levels each add surface the footprint method cannot see; measure those planes separately and add them.

    What the footprint method can and cannot see

    • Overhangs: eaves and rakes extend beyond the walls. For material ordering, add twice the overhang to each building dimension (a 1 ft eave adds 2 ft to length and width).
    • Dormers and additions: any plane not covering the main rectangle must be measured and added separately.
    • Multiple pitches: if part of the roof is steeper (a porch, a turret), split the footprint and apply each section's own multiplier.
    • What it's perfect for: budgeting, comparing quotes, and ordering for simple gable and hip roofs — the large majority of US homes.

    When a quote's square count differs from yours by more than about 5%, ask the roofer to show their measurement. Satellite measurement reports are the usual source, and they are good — but they price dormers and overhangs you may or may not have.

    Frequently asked questions

    How do I calculate my roof's square footage?

    Multiply your home's footprint (length × width) by the pitch multiplier for your slope: √(1 + (pitch/12)²). At 6/12 that's ×1.118. A 1,200 sq ft footprint at 6/12 gives 1,342 sq ft of roof. Divide by 100 for roofing squares.

    How many squares is a 1,500 sq ft roof?

    If 1,500 sq ft is the true sloped area, it is exactly 15 squares. If 1,500 sq ft is the home's footprint or floor area, the roof is bigger: at 6/12 pitch a 1,500 sq ft footprint carries about 1,677 sq ft of roof — 16.8 squares.

    Does roof pitch change the square footage?

    Yes, substantially. The steeper the pitch, the more surface sits over the same footprint: +6% at 4/12, +12% at 6/12, +19% at 8/12 and +41% at 12/12. This is the single most common reason homeowner estimates come in low.

    Should I include overhangs in the footprint?

    For ordering materials, yes: add twice the eave overhang to both building dimensions. A 40×30 ft house with 1 ft overhangs is measured as 42×32 ft. For a rough budget, the walls-only footprint plus the waste allowance usually covers it.

    How accurate is the footprint method?

    For simple gable roofs, within a few percent — good enough for budgets and material orders with a waste allowance. Complex roofs with dormers, valleys and several levels should be measured plane by plane or by satellite report.

    Sources & data

    Geometry: standard rise-over-run roof mathematics — pitch multiplier = √(1 + (rise/12)²), rafter length from the Pythagorean theorem — as published in roofing measurement references and framing practice.

    Data retrieved: 17 Nov 2026.

    Disclaimer: This page gives a preliminary estimate, not a contractor quote. Figures are based on national published cost ranges and standard geometry, with the assumptions shown on the page. Your actual price or measurement will vary with location, roof complexity and condition, material grade, and contractor. Always obtain written quotes and verify critical measurements before buying materials.

    Related calculators & guides

    Keep going with the tools and guides homeowners use alongside this one:

    Roof Pitch Calculator

    Convert rise and run into pitch, angle in degrees, slope percent, multiplier and rafter length.

    Roof Shingle Calculator

    Squares, bundles and underlayment rolls for your roof, with a cost range.

    Roofing Cost Calculator

    A quick general roofing cost estimate per square foot and in total, for any material.

    Roof Sheathing Calculator

    How many 4×8 OSB or plywood sheets your roof deck needs, with waste.

    Hip Roof Calculator

    Hip rafter length, ridge length and roof area for an equal-pitch hip roof.