US Roof Calculator

Underlayment Calculator: Roll Count for Your Roof

Underlayment is bought by the roll, and rolls are rated by how much roof they cover at standard laps — about 1,000 sq ft for synthetics, 432 for 15# felt, 216 for 30# felt. Enter your roof area and pitch: below 4/12 the code's double-coverage rule doubles the area, and this calculator applies it automatically.

Home › Underlayment Calculator

Calculate your underlayment rolls

Your underlayment figures

Rolls needed
—
Area to cover
—

    Roll coverages are manufacturer-published figures at standard laps. Ice-and-water shield for eaves and valleys is a separate product and a separate count.

    How roll counts are calculated

    Rolls = roof area ÷ coverage per roll, rounded UP Low slopes (under 4/12): area counts TWICE — two layers, half-lap

    Worked examples. A 2,070 sq ft roof at 6/12 in synthetic: 2,070 ÷ 1,000 = 2.07 → 3 rolls. The same product logic on a low-slope roof: 1,000 sq ft at 3/12 counts double (2,000 sq ft), and in 15# felt that's 2,000 ÷ 432 = 4.63 → 5 rolls. Low-slope roofs consume underlayment at twice the rate — the most common under-order in this category.

    Why the double-coverage rule exists

    On a shallow slope, water moves slowly and can back up under laps. Building codes therefore require two layers of underlayment (each course lapped halfway over the previous — "half-lap") for shingle roofs between 2/12 and 4/12, or a full membrane such as ice-and-water shield. Below 2/12, shingles themselves are off the table and you are in membrane-roofing territory entirely. The coverage figures on the rolls already assume standard laps at normal pitch — the doubling is the extra the low slope demands.

    Synthetic vs felt

    Synthetics cover roughly 1,000 sq ft per roll (a 10-square roll), lie flat, resist tearing in wind, and can sit exposed longer during the job. Felts are cheaper per roll but cover far less — 15# felt about 432 sq ft (4 squares), 30# about 216 sq ft (2 squares) because the heavier sheet comes in a shorter roll — and they wrinkle when wet. Per square covered, the price gap is much smaller than the per-roll gap suggests.

    What this calculator does not count

    • Ice-and-water shield: the self-adhering membrane at eaves (typically the first 3–6 ft, or to 24 in inside the wall line), valleys, and around penetrations. It is sold and counted separately, by the roll and by the linear feature it protects.
    • Drip edge and flashing: metal work, counted by the linear foot, not the roll.
    • Ridge and hip cap underlayment details: negligible area, covered by the round-up.

    If your quote shows underlayment rolls well above this calculator's count on a normal-pitch roof, ask which product and coverage the estimator assumed — felt's small rolls make honest counts look large, and synthetic counts should be close to area ÷ 1,000.

    Frequently asked questions

    How many rolls of underlayment do I need?

    Divide your roof area by the product's coverage and round up: synthetics cover ~1,000 sq ft per roll, 15# felt ~432 sq ft, 30# felt ~216 sq ft. A 2,000 sq ft roof needs 2 synthetic rolls, 5 rolls of 15# felt, or 10 rolls of 30# felt at normal pitch.

    Why does a low-slope roof need double underlayment?

    Between 2/12 and 4/12 pitch, water drains slowly and can back up under single laps, so codes require two layers applied half-lap (or a full self-adhering membrane). That doubles the area to cover — a 1,000 sq ft low-slope roof consumes underlayment like a 2,000 sq ft roof.

    How much does a roll of synthetic underlayment cover?

    About 1,000 sq ft (10 squares) per roll at the standard 4-inch lap — the common '10-square roll'. Check your product's stated coverage; some lighter synthetics claim more by assuming tighter laps.

    Is synthetic underlayment better than felt?

    For most re-roofs, yes in practice: it covers more per roll, resists wind tear-off during installation, doesn't wrinkle when damp, and tolerates exposure if weather delays the job. Felt costs less per roll but needs 2–5× as many rolls, which narrows the real price difference.

    Do I need ice-and-water shield as well?

    In cold climates, almost certainly at the eaves — code typically requires it from the eave to at least 24 inches inside the exterior wall line — and it's standard practice in valleys and around chimneys and skylights everywhere. It's a separate product from field underlayment and is counted by the feature, not the roof area.

    Sources & data

    Roll coverages: manufacturer-published coverage at standard laps — synthetic underlayment ~1,000 sq ft/roll, 15# felt ~432 sq ft/roll, 30# felt ~216 sq ft/roll. Double coverage: the low-slope underlayment provisions for 2/12–4/12 shingle roofs in the International Residential Code. Data retrieved: 17 Nov 2026.

    Disclaimer: This page gives a preliminary estimate, not a contractor quote. Figures are based on national published cost ranges and standard geometry, with the assumptions shown on the page. Your actual price or measurement will vary with location, roof complexity and condition, material grade, and contractor. Always obtain written quotes and verify critical measurements before buying materials.

    Related calculators & guides

    Keep going with the tools and guides homeowners use alongside this one:

    Roof Shingle Calculator

    Squares, bundles and underlayment rolls for your roof, with a cost range.

    Roof Area Calculator

    True roof square footage and roofing squares from footprint and pitch.

    Roof Waste Calculator

    The right waste percentage for your roof's complexity — and how much extra to order.

    Roof Pitch Multiplier Chart

    Every pitch from 1/12 to 12/12: angle, slope percent, multiplier and best materials.

    Roof Sheathing Calculator

    How many 4×8 OSB or plywood sheets your roof deck needs, with waste.