US Roof Calculator

Gutter Size Calculator: Gutters & Downspouts

Gutters fail by capacity, not by looks: a run that drains too much roof overflows in every hard rain, no matter how new it is. Enter the roof area draining into one gutter run and the run's length, and get the standard sizing answer — 5″ or 6″ K-style gutter, downspout size, and how many downspouts the run needs.

Home › Gutter Size Calculator

Calculate your gutter size

Your gutter sizing

Gutter size
—
Downspouts
—
Downspout size
—

    Sizing follows the standard published drainage table shown below, at standard rainfall intensity. Regions with extreme rainfall rates should size one step up.

    The standard gutter sizing table

    Roof area draining to the runGutter (K-style)DownspoutDownspout spacing
    Up to 750 sq ft5 inch2×3 inch1 per 40 ft of run
    751 – 1,400 sq ft6 inch3×4 inch1 per 40 ft of run
    Over 1,400 sq ft6 inch3×4 inch1 per 30 ft of run

    This is the sizing table published in US gutter and sheet-metal guidance, at a standard design rainfall intensity. Two adjustments sit on top of it. Rainfall: the Gulf Coast and Florida design for far heavier downpours than the Pacific Northwest — in high-intensity regions, size one band up. Pitch: a steep roof accelerates water; some installers apply a pitch factor to the drainage area above 8/12. When in doubt between bands, take the larger: the price difference between 5″ and 6″ gutter is small, and the 6″ carries roughly 40% more water.

    Worked example. A run draining 750 sq ft over an 80 ft eave: 750 sq ft is the top of the first band → 5″ K-style gutter, and 80 ÷ 40 = 2 downspouts in 2×3″. Let the same eave drain 900 sq ft (a bigger roof plane) and the answer steps up to 6″ gutter with 3×4″ downspouts.

    Downspouts: the half everyone undersizes

    Gutters rarely overflow because the trough is small; they overflow because the water cannot get down fast enough. The rules that keep a system honest: one downspout per 40 ft of run (30 ft on the largest drainage areas), a downspout sized to the band in the table — a 3×4″ downspout moves roughly twice the water of a 2×3″ — and a gutter sloped 1/16 to 1/8 inch per foot toward each outlet, with a high point in the middle of long runs so no section drains more than about 40 ft in one direction.

    Where does the "area draining to this run" come from? Add up the sloped areas of the planes that feed the eave — the roof area calculator gives you each plane's area from its footprint and pitch. Upper roofs that discharge onto lower roofs count toward the lower gutter's total, a detail missed on many split-level homes.

    Frequently asked questions

    Do I need 5 inch or 6 inch gutters?

    By drainage area: up to about 750 sq ft per run works with 5″ K-style; 751–1,400 sq ft needs 6″; beyond that stays 6″ but adds downspouts every 30 ft. In heavy-rainfall regions, or with steep pitches, size one band up.

    How many downspouts do I need?

    One per 40 ft of gutter run as the standard rule — an 80 ft eave needs two — and one per 30 ft when a run drains more than about 1,400 sq ft. Every downspout should also sit where its discharge can be carried away from the foundation.

    What size downspout goes with 6 inch gutters?

    3×4 inch. Pairing a 6″ gutter with small 2×3″ downspouts wastes the gutter's extra capacity, because the downspout becomes the bottleneck — the system drains at the speed of its narrowest part.

    Why do my gutters overflow in heavy rain?

    In order of likelihood: the run drains more roof than its band allows, too few or too-small downspouts, lost slope (sagging runs pond instead of draining), or debris. Capacity problems show up even with clean gutters — that's the tell that separates sizing from maintenance.

    How much slope should a gutter have?

    About 1/16 to 1/8 inch per foot toward the downspout — nearly invisible from the ground, but enough to keep water moving and prevent standing water that breeds mosquitoes and adds weight.

    Sources & data

    Sizing table: the standard published K-style gutter and downspout sizing table used in US sheet-metal and gutter installation guidance (drainage-area bands of 750 and 1,400 sq ft; downspout spacing of 40 ft, tightening to 30 ft at the largest band). Data retrieved: 17 Nov 2026. Local rainfall intensity data (NOAA) governs final design in high-rainfall regions.

    Disclaimer: This page gives a preliminary estimate, not a contractor quote. Figures are based on national published cost ranges and standard geometry, with the assumptions shown on the page. Your actual price or measurement will vary with location, roof complexity and condition, material grade, and contractor. Always obtain written quotes and verify critical measurements before buying materials.

    Related calculators & guides

    Keep going with the tools and guides homeowners use alongside this one:

    Roof Area Calculator

    True roof square footage and roofing squares from footprint and pitch.

    Roof Replacement Cost Calculator

    Low, typical and high replacement estimates from your roof size, pitch and material — the site's pillar tool.

    Roof Pitch Calculator

    Convert rise and run into pitch, angle in degrees, slope percent, multiplier and rafter length.

    Hip Roof Calculator

    Hip rafter length, ridge length and roof area for an equal-pitch hip roof.

    Roofing Cost Calculator

    A quick general roofing cost estimate per square foot and in total, for any material.